Authorized Distributor
?
Closed loop (compensated) current transducer using the Hall effect
| Primary Current, Measuring Range | 0 .. ± 2000 A |
| Conversion Ratio (KN) | 1 : 5000 |
| Secondary Nominal RMS Current (ISN) | 200 mA |
| Response Time to 90 % of IPN Step | < 1 µs |
| Isolation Test Voltage (50 Hz, 1 min) | 6 kV |
| Operating Temperature Range | - 10 .. + 85 °C |
AC variable speed drives and servo motor drives, Static converters for DC motor drives, Battery supplied applications, Uninterruptible Power Supplies (UPS), Switched Mode Power Supplies (SMPS), Power supplies for welding applications. Application Domain, Industrial.
The LT 1005-T is a closed loop (compensated) current transducer from LEM for the electronic measurement of currents: DC, AC, pulsed..., with galvanic isolation.
It offers excellent accuracy, very good linearity, low temperature drift and wide frequency bandwidth. Typical applications include AC variable speed drives and servo motor drives, Static converters for DC motor drives, Battery supplied applications and Uninterruptible Power Supplies (UPS).
Key characteristics from the official datasheet: linearity error < 0.1 %; frequency bandwidth DC .. 150 kHz; operating temperature - 10 .. + 85 °C.
| General Information | |
|---|---|
| Manufacturer | LEM |
| Product Series | LT |
| Product Reference | LT 1005-T |
| Primary Nominal Current | 1000 A |
| Supply Voltage | ± 15 .. 24 V |
| Measurement | currents: DC, AC, pulsed... |
| Mounting | Busbar Mount |
| Application Domain | Industrial |
| Electrical Data — LT 1005-T | |
|---|---|
| Primary Nominal RMS Current (IPN) | 1000 A |
| Primary Current, Measuring Range (IPM) | 0 .. ± 2000 A |
| Secondary Nominal RMS Current (ISN) | 200 mA |
| Conversion Ratio (KN) | 1 : 5000 |
| Supply Voltage (UC) | ± 15 .. 24 V |
| Current Consumption (IC) | 30 (@ ± 24V) + IS mA |
| Accuracy & Dynamic Performance | |
|---|---|
| Overall Accuracy @ IPN, TA = 25 °C (XG) | ± 0.4 % |
| Linearity Error (εL) | < 0.1 % |
| Offset Current @ IP = 0, TA = 25 °C (IO) | ± 0.4 mA |
| Magnetic/Residual Offset Current (IOM) | ± 0.2 mA |
| Temperature Variation of IO (Max) | ± 0.5 mA |
| Response Time to 90 % of IPN Step (tr) | < 1 µs |
| di/dt Accurately Followed | > 50 A/µs |
| Frequency Bandwidth (-1 dB) (BW) | DC .. 150 kHz |
| Insulation Coordination | |
|---|---|
| RMS Voltage for AC Insulation Test (50 Hz, 1 min) Ud | 6 kV |
| Creepage Distance (dCp) | 51.8 mm |
| Clearance (dCI) | 44.1 mm |
| Comparative Tracking Index (CTI) | 225 |
| Overvoltage Category / Pollution Degree | Over voltage category OV · Pollution degree PD2 |
| Environmental & Mechanical Characteristics | |
|---|---|
| Ambient Operating Temperature (TA) | - 10 .. + 85 °C |
| Ambient Storage Temperature (TA st) | - 25 .. + 100 °C |
| Secondary Coil Resistance @ TA = 70 °C (RS) | 43 Ω |
| Standards & Certifications | |
|---|---|
| EN 50178 | Compliance |
Note: Specifications are taken from the official LT 1005-T datasheet. Parameters that could not be confirmed from the datasheet are marked UNVERIFIED.
Official technical documentation for the LT 1005-T.
Outline dimensions, pin layout and connection diagrams of the LT 1005-T are shown below.
Note: All dimensions are in millimetres. Refer to the official datasheet for the complete dimension drawing.
Typical applications of the LT 1005-T.
Characteristic curve diagrams are not included in the LT 1005-T datasheet; the relevant characteristics are the accuracy and dynamic performance data listed below.
| Accuracy & Dynamic Characteristics | |
|---|---|
| Overall Accuracy @ IPN, TA = 25 °C (XG) | ± 0.4 % |
| Linearity Error (εL) | < 0.1 % |
| Response Time to 90 % of IPN Step (tr) | < 1 µs |
| di/dt Accurately Followed | > 50 A/µs |
| Frequency Bandwidth (-1 dB) (BW) | DC .. 150 kHz |
Note: For the full set of performance data, refer to the datasheet.
Other models of the LT Series share the same measurement principle, mounting concept and output interface family.
